Our workshop has a CR-10S printer supporting our R&D department. We chose it for positive user reviews and the many modifications available. Our approach has been to take it apart, reassemble it and see whether it still works — so far, it does.

Apart from the frame and motors, little now remains of the original printer. We will describe the modifications gradually, including some that proved unsuccessful.

Noise — the printer is extremely loud. It sounds like a small vacuum cleaner or an early-2000s 450 W PC power supply with an additional graphics card fan.
Start by considering the hotend fans and ventilation of the power supply and mainboard. Reports of CR-10 mainboard overheating prompted us to improve cooling. Note that our CR-10S already has a newer version 1.3 board addressing earlier issues, plus an additional enclosure fan.

Nevertheless, we looked inside and found three fans:

  • A fan inside the power supply,
  • A fan blowing directly onto the mainboard,
  • An exhaust fan removing air from the enclosure.

I had never heard fans this loud, apparently 40 and 50 mm models.
We removed them all. Without quiet replacements available, we printed a base for two large 120 mm fans: one Noctua and one super-silent model. One draws air in and the other exhausts it, producing far more cooling than necessary. The lesson is simply to replace the original low-end fans with better ones. The result was around 70% quieter, with no more comparisons to a vacuum cleaner.

Replacement means connecting the new fans in place of the old ones while preserving polarity and wire colours.
Old connections can be desoldered or cut, then joined to the new fan by soldering or suitable connectors. Leave enough wire to avoid having to extend it later.

We could not find our original design, but the following projects may provide inspiration:
https://www.thingiverse.com/thing:2852221
https://www.thingiverse.com/thing:2809626

Next we replaced both hotend cooling fans. This required changing the duct system: Creality uses one standard 40 mm fan and one blower, while we chose two 40 mm Noctua fans. We replaced the standard assembly with a design from: https://bantam.design/mount — choose a suitable configuration, log in and receive the printable design by email. It is a well-developed project worth considering. We also added BLTouch, which deserves a separate article.

Things to watch for and points that may concern a home maker:

  • Higher-end fans have an extra feedback wire. It is not required for this application and can be left unused.
  • The power supply receives 230 V mains power and must be treated carefully. Disconnect the equipment before dismantling it or replacing components; remember this even when the precaution seems obvious.
  • Wires, cables and tanglesThe CR-10S wiring layout needs improvement. We extended cables and fitted separate connectors, to be described in another article. Connections can use suitable terminals or soldering. We first used connectors for speed, then soldered once the configuration was confirmed.
  • Screws, bolts and nuts — Plan ahead. Without workshop supplies, discovering on Friday evening that one screw is too short can stop printing until Monday. Original hardware does not always fit modified assemblies.
  • Fan performance — Consider cooling capacity. Two 40 mm fans seemed sufficient for PLA at 220°C, but a future hotend change may require more airflow. Plan once rather than redesigning later; learn from our mistakes.

If you have questions, ask us. We are happy to help, advise or work through a solution together.

Update: when replacing fans, check rotational speed as well as the stated noise level.
Most CR-10S and CR-10 fans run at constant voltage and effectively full speed continuously.
A small 40 mm fan rated at 16 dB may sound more intrusive than an 80 mm fan with a similar rating because it runs at around 4,500 rpm rather than 2,000 rpm. This affects perceived noise, especially for the power supply and enclosure fans.
Replacing two small fans with one larger fan can be better than buying expensive small models. Our 120 mm fans provide excessive airflow, but also very quiet operation.

 

Contact: [email protected]

Future parts will cover:

  1. Installing a bed-position sensor — BLTouch — and whether it is worthwhile,
  2. Installing new firmware and choosing a version,
  3. Bed levelling and print setup: coping when everything initially goes wrong,
  4. Further noise reduction measures.

 

* Topics are in no particular order; further parts are coming soon.